说明书 飞利浦 RQ331 剃须刀

说明书

- Water may drip from the socket at the bottom

of the shaver when you rinse it. This is normal

and not dangerous because all electronics

are enclosed in a sealed power unit inside

the shaver.

Electromagnetic elds (EMF)

- This Philips appliance complies with all

applicable standards and regulations regarding

exposure to electromagnetic elds.

General

- This shaver is waterproof. It is suitable for use

in the bath or shower and for cleaning under

the tap. For safety reasons, the shaver can

therefore only be used without cord (Fig. 2).

- The appliance is suitable for mains voltages

ranging from 100 to 240 volts.

- The adapter transforms 100-240 volts to

a safe low voltage of less than 24 volts.

- Maximum noise level: Lc = 69dB(A)

General description (Fig. 3)

1 Protection cap

2 Shaving unit with shaving head holder

3 Shaving head holder release buttons

4 On/off button

5 ’Battery low’ light

6 Retaining ring

7 Cutter

8 Shaving guard

9 Shaving head holder

10 Trimmer (RQ350 only)

11 Adapter

12 Charging light

13 Small plug

14 Cleaning brush

Charging

It takes approx. 10 hours to fully charge the battery.

A fully charged shaver provides up to 30 shaving

minutes.

If you have a heavy beard, the shaver may

provide less than 30 shaving minutes. The number

of shaving minutes may also vary over time,

depending on your shaving behaviour, cleaning

habits and beard type.

’Charging’ indication

- When the shaver is charging, the light on the

adapter lights up (Fig. 4).

’Battery low’ light

- When the battery is almost empty, the light on

the shaver lights up (Fig. 5).

Charging

Do not charge the shaver in the packaging.

1 Put the small plug in the shaver.

2 Put the adapter in the wall socket.

, The light on the adapter lights up to show

that the shaver is charging.

Note: The light on the adapter does not change colour

and does not go out when the shaver is fully charged.

Using the shaver

Note: You cannot use the shaver while it is connected

to the mains.

Shaving

Skin adaptation period

Your rst shaves may not bring you the result you

expect and your skin may even become slightly

irritated. This is normal. Your skin and beard need

time to adapt to any new shaving system.

We advise you to shave regularly (at least 3 times

a week) for a period of 3 weeks to allow your skin

to adapt to the new shaver. During this period, use

your new electric shaver exclusively and do not use

other shaving methods. If you use different shaving

methods, it is more difcult for your skin to adapt

to the new shaving system.

1

Press the on/off button to switch on the shaver.

2 Move the shaving heads over your skin.

Make both straight and circular movements

(Fig. 6).

3

Press the on/off button to switch off the shaver.

4 Clean the shaver after every shave

(see chapter ‘Cleaning and maintenance’).

Trimming (RQ350 only)

You can use the trimmer to groom your sideburns

and moustache.

1 Pull the shaving unit straight off the shaver

(Fig. 7).

Note: Do not twist the shaving unit while you pull it

off the shaver.

2 Insert the lug of the trimmer into the slot in

the top of the shaver (1). Then press down

the trimmer (2) to attach it to the shaver

(‘click’) (Fig. 8).

3 Press the on/off button to switch on the

trimmer. You can now start trimming.

4 Press the on/off button to switch off

the trimmer.

5 Pull the trimmer straight off the shaver

(Fig. 9).

Note: Do not twist the trimmer while you pull it off

the shaver.

6 Insert the lug of the shaving unit into the slot

in the top of the shaver (1). Then press down

the shaving unit (2) to attach it to the shaver

(‘click’) (Fig. 10).

Cleaning and maintenance

Detach the handheld part from the supply cord

before cleaning it in water.

Never use scouring pads, abrasive cleaning agents

or aggressive liquids such as petrol or acetone to

clean the shaver and its accessories.

- Clean the shaver after every shave.

- Clean the shaving heads frequently with Philips

Shaving Head Cleaning Spray (HQ110) for

optimal shaving performance.

- You can clean the outside of the shaver with

a damp cloth. Do not clean the shaving unit

with a cloth.

Cleaning the shaving unit

Be careful with hot water. Always check if the

water is not too hot, to prevent your hands from

getting burnt.

1 Switch off the shaver, remove adapter from

wall socket and pull the appliance/small plug

out of the shaver.

2 Rinse the shaving unit under a hot tap for

some time (Fig. 11).

Note: You can also clean the shaving unit with the

cleaning brush supplied.

3 After rinsing the appliance under the tap,

hold it upright for 10-15 seconds to allow

water to run out of the bottom.

4 Press the release buttons on the shaving unit

(1) and pull the shaving head holder off the

shaving unit (2). (Fig. 12)

5 Rinse the shaving head holder under a hot

tap for 30 seconds (Fig. 13).

Note: You can also clean the shaving head holder with

the cleaning brush supplied.

6 Carefully shake off excess water and let the

shaving head holder dry.

Never dry the shaving head holder with a towel

or tissue, as this may damage the shaving heads.

7 Reattach the shaving head holder to the

shaving unit (‘click’) (Fig. 14).

Extra-thorough cleaning method

1 Switch off the shaver.

2 Press the release buttons on the shaving unit

(1) and pull the shaving head holder off the

shaving unit (2) (Fig. 15).

3 To unlock the orange retaining ring, turn it in

the direction of the arrows indicated in and

on the retaining ring (Fig. 16).

4 Lift the retaining ring out of the shaving head

holder. (Fig. 17)

5 Remove the cutter and the shaving guard

(Fig. 18).

Note: Do not clean more than one cutter and shaving

guard at a time, since they are all matching sets.

If you accidentally put a cutter in the wrong shaving

guard, it may take several weeks before optimal

shaving performance is restored.

6 Clean the cutter with the cleaning brush

supplied (Fig. 19).

7 Clean the inside of the shaving guard (Fig. 20).

8 After cleaning, place the shaving guard back

into the shaving head holder. Make sure the

two wings t exactly into the recesses of the

shaving head holder (Fig. 21).

9

Place the cutter back into the shaving guard

with the cutter legs pointing downwards

(

Fig. 22).

10 Place the retaining ring back onto the shaving

head holder (1). To reattach the retaining ring,

turn it against the direction of the arrows

indicated in and on the retaining ring (2)

(Fig. 23).

Note: Make sure the retaining ring is xed properly.

The four wings of the retaining ring have to be

located exactly under the recesses of the shaving

head holder (Fig. 24).

11 Reattach the shaving head holder to the

shaving unit (‘click’). (Fig. 14)

Note: If the shaving unit does not close smoothly,

check if you have positioned the shaving heads

properly and if the retaining rings are xed properly.

常见问题

有关本说明书的更多信息

我们知道，为您的 飞利浦 RQ331 剃须刀 提供纸质手册是件好事。 您随时可以从我们的网站下载该手册并自行打印。 如果您想要原始手册，我们建议您联系Philips。 他们也许能够提供原始手册。 您是否正在寻找其他语言版本的 飞利浦 RQ331 剃须刀 手册？ 在我们的主页上选择您的首选语言并搜索型号以查看我们是否有可用。

规格

飞利浦 剃须刀 的所有手册
剃须刀 的更多手册

关于 飞利浦 RQ331 剃须刀 的常见问题

我们的支持团队将搜索有用的产品信息并回答常见问题。如果您在常见问题中发现不准确的回答，请使用联系表格告知我们。

相关产品

说明书

飞利浦 AT798 AquaTouch 剃须刀

说明书

飞利浦 BRL136 剃须刀

说明书

飞利浦 PT786 剃须刀

说明书

飞利浦 RQ311 剃须刀

说明书

飞利浦 QP2527 One Blade 剃须刀

说明书

飞利浦 RQ361 剃须刀

说明书

飞利浦 BRL160 SatinShave Prestige 剃须刀

说明书

飞利浦 RQ330 剃须刀

相关类别