说明书 飞利浦 S566 剃须刀

说明书

ENGLISH

Congratulations on your purchase and

welcome to Philips! To fully benet from

the support that Philips oers, register

your product at www.philips.com/

welcome.

General description (Fig. 1)

1 Protection cap

2 Shaving head holder

3 Shaving unit connector

4 Handle

5 Battery charge indicator

6 On/o button

7 Socket for small plug

8 Cutter

9 Guard

10 Retaining frame

11 Supply unit

12 Small plug

Not shown: cleaning brush

Important safety

information

Read this important information

carefully before you use the appliance

and its accessories and save it for future

reference. The accessories supplied may

vary for dierent products.

Danger

- Keep the supply unit dry (Fig. 2).

Warning

- To charge the battery, only use the

detachable supply unit (HQ8505)

provided with the appliance.

- The supply unit contains a

transformer. Do not cut o the

supply unit to replace it with

another plug, as this causes a

hazardous situation.

- This appliance can be used by

children aged from 8 years and

above and persons with reduced

physical, sensory or mental

capabilities or lack of experience and

knowledge if they have been given

supervision or instruction concerning

use of the appliance in a safe

way and understand the hazards

involved. Children shall not play with

the appliance. Cleaning and user

maintenance shall not be made by

children without supervision.

- Always unplug the shaver before

you clean it under the tap.

- Always check the appliance before

you use it. Do not use the appliance

if it is damaged, as this may cause

injury. Always replace a damaged

part with one of the original type.

- Do not open the appliance to

replace the rechargeable battery.

Caution

- Never use water hotter than 60°C to

rinse the shaver.

- Only use this appliance for its

intended purpose as shown in the

user manual.

- For hygienic reasons, the appliance

should only be used by one person.

- Never use compressed air, scouring

pads, abrasive cleaning agents or

aggressive liquids such as petrol or

acetone to clean the appliance.

- Water may drip from the bottom of

the shaver when you rinse it. This is

normal and not dangerous because

all electronics are enclosed in a

sealed power unit inside the shaver.

- Do not use the supply unit in or near

wall sockets that contain an electric

air freshener to prevent irreparable

damage to the supply unit.

Electromagnetic elds (EMF)

- This Philips appliance complies

with all applicable standards and

regulations regarding exposure to

electromagnetic elds.

General

- This shaver is waterproof (Fig. 3).

It is suitable for use in the bath or

shower and for cleaning under the

tap. For safety reasons, the shaver

can therefore only be used without

cord.

- The appliance is suitable for mains

voltages ranging from 100 to 240 volts.

- The supply unit transforms 100-

240 volts to a safe low voltage of

less than 24 volts.

Charging

Note: This appliance can only be used

without cord.

Charge the appliance before rst use

and when the display indicates that

the battery is almost empty.

Charging takes approx. 1 hour.

A fully charged shaver provides up to

45 minutes of shaving time.

Charging with the supply unit

1 Put the small plug in the shaver.

2 Put the supply unit in the wall

socket (Fig. 4).

3 After charging, remove the supply

unit from the wall socket and pull

the small plug out of the appliance.

Charge indications

Battery low

S586: When the battery is almost

empty, the bottom light of the battery

charge indicator ashes orange (Fig. 5).

S566: When the battery is almost

empty, the battery charge indicator

ashes orange.

Battery charging

S586: When the appliance is charging,

the bottom light of the battery charge

indicator rst ashes and then lights

up continuously (Fig. 6). After this the

second light ashes and then lights

up continuously, and so on until the

appliance is fully charged.

S566: When the appliance is charging,

the battery charge indicator ashes white.

Battery full

S586: When the battery is fully charged,

all lights of the battery charge indicator

light up white continuously (Fig. 7).

S566: When the battery is fully

charged, the battery charge indicator

lights up white continuously.

Note: This appliance can only be used

without cord.

‚Unplug before use‘ reminder

S586: All lights of the battery charge

indicator ash 3 times to remind you to

unplug the shaver rst.

S566: The battery charge indicator

ashes fast briey to remind you to

unplug the shaver rst.

Using the appliance

Removing or attaching the

click-on attachments

1 Make sure the appliance is

switched o.

2 Insert the lug of the attachment into

the slot in the top of the appliance.

Then press down the attachment

to attach it to the appliance (‘click’)

(Fig. 8).

3 Pull the attachment straight o the

appliance (Fig. 9).

Note: Do not twist the attachment

while you pull it o the appliance.

Switching the appliance on

and o

1

To switch the appliance on or o,

press the on/o button once (Fig. 10).

Note: This appliance can only be used

without cord.

Shaving

Skin adaptation period

Your rst shaves may not bring you the

result you expect and your skin may

even become slightly irritated. This is

normal. Your skin and beard

need time to adapt to any new shaving

system. To allow your skin to adapt

to this new appliance, we advise you

to shave regularly (at least 3 times

a week) and exclusively with this

appliance for a period of 3 weeks.

Dry shaving

1 Switch on the appliance.

2

Move the shaving heads over your

skin in circular movements to catch

all hairs growing in dierent directions

(Fig. 11). Exert gentle pressure for a

close, comfortable shave.

Note: Do not press too hard, as this

can cause skin irritation.

3 Clean the appliance after use

(see ‚Cleaning and maintenance‘).

Wet shaving

You can also use this appliance on a wet

face with shaving foam or shaving gel.

To shave with shaving foam or shaving

gel, follow the steps below:

1 Apply some water to your skin.

2 Apply shaving foam or shaving gel

to your skin.

3 Rinse the shaving unit under the

tap to ensure that the shaving unit

glides smoothly over your skin.

4 Switch on the appliance.

5

Move the shaving heads over your

skin in circular movements to catch

all hairs growing in dierent directions

(Fig. 11). Exert gentle pressure for a

close, comfortable shave.

Note: Do not press too hard, this

can cause skin irritation.

Note: Rinse the shaving unit

regularly to ensure that it continues

to glide smoothly over your skin.

6 Dry your face.

7 Clean the appliance after use

(see ‚Cleaning and maintenance‘).

Note: Make sure you rinse all foam

or shaving gel o the appliance.

Storage

Always slide the protection cap onto

the shaving unit to protect the shaving

unit from dirt or damage during

traveling or storage (Fig. 24).

We advise you to let the appliance dry

before you store it.

Ordering accessories

To buy accessories or spare parts,

visit www.shop.philips.com/service

or go to your Philips dealer. You can

also contact the Philips Consumer

Care Center in your country (see

the international warranty leaet for

contact details).

Available parts

The following accessories and spare

parts are available:

- SH30 Philips shaving heads

- RQ575 Philips cleansing brush

attachment

- RQ563 Philips cleansing brush

attachment 3-pack

- HQ110 Cleaning spray

- HQ8505 supply unit

Note: Availability of the accessories

may dier by country.

Recycling

- Do not throw away the product

with the normal household waste

at the end of its life, but hand it in

at an ocial collection point for

recycling. By doing this, you help to

preserve the environment.

- This product contains a built-in

rechargeable battery which shall

not be disposed of with normal

household waste. We strongly

advise you to take your product

to an ocial collection point

or a Philips service centre to

have a professional remove the

rechargeable battery.

- Follow your country’s rules for the

separate collection of electrical

and electronic products and

rechargeable batteries. Correct

disposal helps prevent negative

consequences for the environment

and human health.

Removing the rechargeable

battery

Only remove the rechargeable

battery when you discard the shaver.

Before you remove the battery, make

sure that the shaver is disconnected

from the mains and that the battery

is completely empty.

Take any necessary safety

precautions when you handle tools

to open the shaver.

Be careful, the battery strips are sharp.

1 Disconnect the appliance from the

wall socket and let the appliance

run until the motor stops.

2 Insert a screwdriver under the

edge of the upper front panel and

remove it (Fig. 25).

3 Undo the screws in the top part of

the shaver (Fig. 26).

4 Remove the cover (Fig. 27).

5 Insert a screwdriver under the edge

of the lower front panel to remove

it (Fig. 28).

6 Remove the inner panel with a

screwdriver (Fig. 29).

7

Push the inner frame out of the

housing with the screwdriver (Fig. 30).

8 Cut the wires from the motor with

pliers (Fig. 31) and remove the

printed circuit board (Fig. 32).

9 Break the battery tags and remove

the batteries (Fig. 33).

Troubleshooting

This chapter summarizes the most

common problems you could encounter

with the appliance. If you are unable to

solve the problem with the information

below, visit www.philips.com/support

for a list of frequently asked questions

or contact the Consumer Care Center in

your country.

Cleaning and maintenance

Cleaning the shaver under the tap

Clean the shaver after every shave for

optimal performance (see ‚Cleaning

and maintenance‘). Always unplug and

switch o the shaver before you clean it.

Never use compressed air, scouring

pads, abrasive cleaning agents or

aggressive liquids such as petrol or

acetone to clean the appliance.

Be careful with hot water. Always

check if the water is not too hot, to

prevent burning your hands.

Never dry the shaving unit with a

towel or tissue, as this may damage

the shaving heads.

1 Rinse the shaving unit under a

warm tap.

Note: You can also clean the

shaving unit with the cleaning brush

supplied (Fig. 12).

2 Turn the shaver up side down and

rinse the openings in the bottom of

the shaving head holders. Switch

on the shaver briey during rinsing

(Fig. 13).

3 Open both shaving head holders

(Fig. 14).

4 Rinse the hair chambers and

shaving head holders under the tap

(Fig. 15).

5 Carefully shake o excess water

and let air dry completely.

6 Close the shaving head holders

(Fig. 16).

Thorough cleaning

The shaving unit consists of two

shaving heads. Clean one shaving

head at a time by following the steps

below.

1 Open the shaving head holder

(Fig. 14).

2

To unlock the retaining frame, gently

squeeze both sides of the retaining

frame and ip open the frame (Fig. 17).

3 Remove the shaving head. Each

shaving head consists of a cutter

and a guard (Fig. 18).

Note: Do not clean more than one

cutter and guard at a time, since

they are all matching sets. If you

accidentally mix up the cutters

and guards, it may take several

weeks before optimal shaving

performance is restored.

4 Remove the cutter from the shaving

guard (Fig. 19).

5 Rinse both parts with water.

6 After cleaning, place the cutter back

into the guard with the cutter legs

pointing downwards (Fig. 20).

7 Put the shaving head back into the

shaving head holder (Fig. 21).

Note: Make sure that the shaving

heads with the projections t

exactly onto the hooks of the

shaving head holder when placing

them (Fig. 23). The shaving heads

supplied with this appliance either

have notches or projections. Both

shaving systems are the same.

8 Push the retaining frame back onto

the shaving head holder until you

hear a click (Fig. 22).

9 Close the shaving head holder

(Fig. 16).

Replacement

Replacing the shaving heads

For maximum shaving performance,

we advise you to replace the shaving

heads every two years. Replace

damaged shaving heads immediately.

Always replace the shaving heads with

original Philips shaving heads (see

‚Ordering accessories‘).

1 Switch o the appliance.

2 Open the shaving unit by opening

both shaving head holders (Fig. 14).

3 To unlock the retaining frames,

gently squeeze both sides of the

retaining frames and ip open the

shaving heads (Fig. 17).

4 Remove the shaving heads from

the shaving head holders (Fig. 18).

Throw away the used shaving

heads immediately to avoid mixing

them with the new shaving heads.

5 Place the new shaving heads in the

shaving head holders.

Note: Make sure that the shaving

heads with the projections t

exactly onto the hooks of the

shaving head holder when placing

them (Fig. 23). The shaving heads

supplied with this appliance either

have notches or projections. Both

shaving systems are the same.

6 Push the retaining frames back onto

the shaving head holder until you

hear a click (Fig. 22).

7 Close the shaving head holders

(Fig. 16).

Prob-

lem

Possible

cause

Solution

The

shaver

does not

work as

well as it

used to.

The

shaving

heads are

damaged

or worn.

Replace

the shaving

heads (see

'Replace-

ment').

The

shaving

heads are

dirty.

Clean the

shaving

heads (see

'Cleaning and

maintenan-

ce').

Long

hairs ob-

struct the

shaving

heads.

Clean the

shaving

heads (see

'Cleaning and

maintenan-

ce').

The

recharge-

able

battery is

low.

Switch o the

shaver and

recharge the

battery (see

'Charging').

The sha-

ver does

not work

when I

switch it

on.

The

recharge-

able

battery is

empty.

Switch o the

shaver and

recharge the

battery (see

'Charging').

The

shaver is

con nect-

ed to

the wall

socket.

This appli-

ance can

only be used

without cord.

Remove the

supply unit

from the wall

socket and

pull the small

plug out of

the appli-

ance.

The

shaving

heads

do not

stay in

place

in the

shaving

unit.

You

did not

x the

retaining

frames

properly.

The retaining

frames are

xed properly

if you hear

a click when

you push it

back onto

the shaving

heads.

The

shaving

heads

with pro-

jec tions

are not

placed

properly.

Make sure

that the sha-

ving heads

with the

projections t

exactly onto

the hooks of

the shaving

head holder

when placing

them (Fig. 23).

简体中文

感谢您的惠顾，欢迎光临飞利

浦！ 为了让您能充分享受飞利

浦提供的支持，请在

www.philips.com/welcome

上注册您的产品。

基本说明（图 1）

1 保护盖

2 剃须刀头支架

3 剃须刀头部件连接器

4 手柄

5 电池充电指示灯

6 开/关按钮

7 小插头插座

8 刀片

9 网罩

10 固定架

11 电源部件

12 小插头

未显示： 清洁刷

重要安全信息

使用本产品及其附件之前，

请仔细阅读本重要信息，

并妥善保管以供日后参考。

随附的附件可能因产品而异。

危险

- 保持电源部件干燥 (图 2)。

- 警告符号注释： 禁止在打开

的水龙头下进行清洗 (图 2)。

警告

- 要给电池充电，请仅使用

产品随附的可拆卸电源部件

(HQ8505)。

- 电源部件中包含一个变压器。

请勿自行更换电源部件的插

头，否则将导致严重后果。

- 本产品也可以由 8 岁或以上

年龄的儿童以及肢体不健全、

感觉或精神上有障碍或缺乏相

关经验和知识的人士使用，但

前提是有人对他们使用本产品

进行监督或指导，以确保他们

安全使用，并且让他们明白相

关的危害。 切勿让儿童玩弄

本产品。 不要让儿童在无人

监督的情况下对本产品进行清

洁和保养。

- 将剃须刀手持部分与电源软

线分开后，才能在水龙头下

清洗手持部分。

- 使用前，请务必检查产品。

请勿使用损坏的产品，否则可

能对人体造成伤害。 请务必

用原装型号更换损坏的部件。

- 切勿拆开本产品更换充电电

池。

警告

- 切勿使用温度高于 60°C

的热水冲洗剃须刀。

- 只能将本产品用于用户手册

中所示的原定用途。

- 出于卫生的目的，本产品只

能供一个人使用。

- 切勿使用压缩气体、钢丝绒、

研磨性清洁剂或腐蚀性液体

（例如汽油或丙酮）来清洁

产品。

- 冲洗剃须刀时，水可能从产

品底部的插口漏出。 这是正

常的，而且没有危险，因为

所有电子元件都封闭在剃须

刀内部的密封电源部件中。

- 请勿在包含电动空气清新器

的墙壁插座上或其周围使用

电源部件，以免电源部件受

到不可修复的损坏。

电磁场 (EMF)

- 本 Philips 产品符合所有有关

暴露于电磁场的适用标准和

法规。

概述

- 符号注释：适合于在洗澡或淋

浴时使用 (图 3)。 允许在盛

水的浴缸、淋浴、洗脸盆或其

他器皿附近使用本器具

。

- 该剃须刀具有防水性能 (图 3)。

适合在沐浴或淋浴时使用，也

可以放在水龙头下清洗。 出于

安全原因，该剃须刀在使用时

不能连接电线。

- 本产品适合在 100 - 240 伏

的电源电压下工作。

- 该电源部件可将 100-240 伏

的电压转换为 24 伏以下的安

全低电压。

充电

注意： 本产品只能在不接电源

的情况下使用。

第一次使用本产品之前，以及

当显示屏指示电池电量快要耗

尽时，请先为本产品充电。

充电约需 1 小时。完全充电的

剃须刀可提供长达 45 分钟的剃

须时间。

使用电源部件充电

1 将小插头插入剃须刀。

2 将电源部件插入电源插座

(图 4)。

3 充电之后，从电源插座上拔

下电源部件，并从产品上拔

下小插头。

4222_002_7319_1_DFU-Leaflet_55x99_6x4_v1.indd 2 05/05/17 11:31

常见问题

有关本说明书的更多信息

我们知道，为您的 飞利浦 S566 剃须刀 提供纸质手册是件好事。 您随时可以从我们的网站下载该手册并自行打印。 如果您想要原始手册，我们建议您联系Philips。 他们也许能够提供原始手册。 您是否正在寻找其他语言版本的 飞利浦 S566 剃须刀 手册？ 在我们的主页上选择您的首选语言并搜索型号以查看我们是否有可用。

规格

飞利浦 剃须刀 的所有手册
剃须刀 的更多手册

关于 飞利浦 S566 剃须刀 的常见问题

我们的支持团队将搜索有用的产品信息并回答常见问题。如果您在常见问题中发现不准确的回答，请使用联系表格告知我们。

相关产品

说明书

飞利浦 PQ228 剃须刀

说明书

飞利浦 FT658 剃须刀

说明书

飞利浦 RQ1187 剃须刀

说明书

飞利浦 HQ6070 剃须刀

说明书

飞利浦 RQ1180CC 剃须刀

说明书

飞利浦 HQ6906 剃须刀

说明书

飞利浦 HP6366 Double Contour Ladyshave Sensitive 剃须刀

说明书

飞利浦 HQ6926 剃须刀

相关类别