说明书 Oregon BAA 223PNH 气象站

说明书

EN

INTRODUCTION

Thank you for selecting the Oregon Scientic™ Projection In/Out Thermo

Clock. This device bundles precise time keeping, alarm, and temperature

monitoring features into a single tool you can use from the convenience

of your home. Keep this manual handy as you use your new product.

It contains practical step-by-step instructions, as well as technical

specications and warnings you should know.

PRODUCT INTRODUCTION

LCD Display

Weather

Forecast

Indicator

Indoor Temperature

Display

Outdoor Temperature

Display

Time Display

LCD Display

Symbol Description Function

Radio signal reception to

outdoor unit (RTHN129)

Indicates the strength of the

radio reception

Low battery

Indicates low battery power of

outdoor unit (RTHN129)

Alarm 1 on

Alarm 2 on

Appears when an alarm is

activated

RF antenna icon

Appears when RF clock data

received

OUT 12345

Outdoor sensor reading

Shows outdoor temperature of

selected sensor.

IN

Indoor sensor reading Shows indoor temperature

ZONE

Time zone Indicates selected time zone

Sunny Weather forecast indicator

Rainy Weather forecast indicator

Snowy Weather forecast indicator

Projection

Time Display Outdoor Temperature Display

(channel 1 only)

NOTE

Focus length (1.5m – 2m)

GETTING STARTED

Connecting the main unit to power supply

Connect the power cable to the Micro USB jack and plug the power

adaptor into a suitable power outlet.

Inserting batteries into remote thermo sensor

• Slide the battery compartment cover open and insert 2 “AAA” batteries,

matching the polarity as shown, then replace the cover.

• Press RESET inside the sensor after each battery change.

Placement of the main unit

Getting started - Line Drawing

Unpacking the product

Placement of the main unit

Connecting the main unit to power Inserting batteries into remote thermo sensor

Max 1.5m

Max 50m

• Place the device as far as possible from computers and microwaves to

avoid interference with reception.

• Only use this device indoors in a dry location.

• Leave space around the device for ventilation purposes, so that the

warm air can escape freely.

• To ensure for good sound quality, do not cover the speaker.

Placement of the remote thermo sensor (RTHN129)

Getting started - Line Drawing

Unpacking the product

Placement of the main unit

Connecting the main unit to power Inserting batteries into remote thermo sensor

Max 1.5m

Max 50m

• Ideal placements for the sensor would be in any location outside the

home at a height of not more than 5 ft (1.5 m), shielded from direct

sunlight or wet conditions.

NOTE

Depending on conditions, the maximum radio signal reach is 50 m.

KEY DESCRIPTIONS

Top

SNOOZE (Backlight / Projection) button

Back

Temperature button Clock button

Set/Alarm button button

button

Micro USB jack Reset button

°C / °F button Light button

Flip 180° button

RADIO RECEPTION

This product is designed to automatically synchronize its calendar and

clock when brought within the range of the radio signal. When the unit

is receiving the signal, the radio reception symbol (RCC) starts to blink.

Depending on the strength of the signal, the connection process takes

2 to 10 minutes. If the signal is weak, it could take up to 24 hours to

receive a valid signal.

Symbol Description Function

RF antenna

icon off

The icon is turned off to indicate that the

main unit has not received RF clock data for

at least 1 hour and 15 minutes.

RF antenna

icon on

The icon is turned on when the main unit has

received RF clock data.The icon will turn off if

no data is received for 1 hour and 15 minutes,

or the clock time is adjusted manually.

The main unit is able to receive RF clock data from remote sensor in DCF

(EU) MSF (UK) and WWVB (US) format:

• DCF (EU) and MSF (UK): The time zone settings within the range of -23

to 23 reference to time zone 0 of the DCF/MSF broadcasting signal.

• WWVB (US): The time zone settings 0/1/2/3 reference to time zones

P/M/C/E of the WWVB broadcasting signal.

Clock signal reception indicator:

Symbol Description

Strong signal

Weak signal

No signal

Receiving signal

Radio reception disabled

NOTE

Reception can be affected by a number of factors. For best

reception, place the device away from metal objects and electrical

appliances. Other causes of signal interference include electrical

transmission towers, steel reinforced construction and metal siding.

Reception is ideal when the unit is placed near a window.

Enabling/disabling radio reception

SEARCH button (located inside the outdoor receiver)

• Press SEARCH to enable the RCC search function. The LED will ash

twice to indicate that search function is enabled.

• Press and hold SEARCH to disable the RCC search function. The LED will

ash three times to indicate that search function is disabled.

SETTING TIME MANUALLY

• Press and hold SEARCH (button is located inside the outdoor

receiver) to disable signal reception.

• Press and hold

. The screen displays ZONE and the number ashes.

• Press once or press and hold

and to adjust the setting. For EU/

UK, the time-zone offset sets the clock up to +/- 23 hours from the

received clock signal time. For US, the time-zone setting is 0(P), 1(M),

2(C), 3(E).

• Press

to conrm.

• Press once or press and hold

and to adjust the setting for 12/24h

hour format, hour, minute, year, calendar format (month-day/day-

month), month, date and temperature unit (°C/°F).

• Press

again to conrm.

DISPLAYING TIME AND DATE

• Press to toggle between time and date display.

ALARM FUNCTION

You can set two different alarm times with this clock.

Setting/adjusting alarm time

• Press and hold

.

• Use

and to adjust the hour and press to conrm.

• Use

and to adjust the minute and press to conrm.

• The alarm time is displayed. The alarm sound will stop after 2 minutes.

Snooze function

• To use the SNOOZE function, press the SNOOZE (light) button on

top of the clock when the alarm sounds. The alarm will stop and start

again after 8 minutes. You can repeat this function three times.

Displaying the alarm time

By default the clock will show the current time and date.

• To display Alarm 1 for 5 sec, press

and .

• To display Alarm 2 for 5 sec, press

and .

Activating/deactivating the alarm

• Press

to activate/deactivate alarm in sequence:

Alarm1 > Alarm 2 > Both ON > Both OFF.

BACKLIGHT

• Press the Light button to toggle the desired backlight display

brightness level.

• To activate the projection and the brightest backlight display for 5

seconds, press the Snooze (light) button.

PROJECTION

The projector displays the time on your ceiling for easy viewing in a

darkened room.

• To activate the backlight and projection function for 5 seconds, press

the SNOOZE (light) button.

NOTE

This function only works when the projection function is turned OFF.

• To turn projection ON and OFF press and hold Light to toggle

between options. (The default setting is ON)

• To ip the projection content by 180°, press Flip 180°.

TEMPERATURE FUNCTION

The temperature is measured in °C or °F.

• Press °C / °F to toggle between Centigrade (°C) and Fahrenheit (°F).

The current indoor temperature is always displayed in the lower right

corner of the LCD display. To receive outdoor temperature information, you

can connect up to 5 remote sensors to the main unit:

• Press

& to toggle between channels (1 to 5) and display the

outdoor temperature of different sensors.

• Press and hold

and for 2 seconds to start searching for remote sensors.

• Press and hold and for 2 seconds to enable auto-scan function for

the 5 channels. Information from Channel 1,2,3,4,5 will automatically

be displayed in sequence.

RESETTING THE CLOCK

Whenever the clock is not behaving as expected, press Reset with the

point of a blunt object such as a stylus or ball point pen.

NOTE

This will return all settings to default values.

REMOTE SENSOR

The main unit can collect temperature data from up to 5 sensors, and

should be placed within 98 ft (50 m) of the main unit. The amber LED

Indicator on the front of the sensor will blink to indicate that the unit is

transmitting a signal.

s

CH Channel 1-5. If more than one sensor is being used, make sure

each one has a different channel number.

EU/UK/US: Select your region for RCC.

SEARCH Press to search for RCC function.

RESET Press if the sensor is not working correctly or if the batteries

have been replaced.

NOTE

Before placing the remote sensor outdoors, check that the battery

compartment door is closed properly,

SPECIFICATIONS

MAIN UNIT

L x W x H 22 x 200 x 80 mm

Weight 224 g without batteries

Operating range -5.0 °C to +50.0 °C (23.0 °F to 122.0 °F)

Temperature resolution 0.1 °C (0.2 °F)

Temperature unit °C/°F

BAA223PNH

REMOTE THERMO SENSOR (RTHN129)

L x W x H 125 x 50 x 19.5 mm

Weight 59 g without batteries

Operating range -20 ºC to +60 ºC (-4 ºF to 140 ºF)

Temperature resolution 0.1 ºC (0.2 ºF)

No. of channel selectable 5

RF Transmission range 50 m

SAFETY

Please observe the following safety precautions when setting up and

using this product.

• The manufacturer assumes no liability for possible damages that may

have been caused by incorrect usage or mishandling of the device.

• Prior to using the device for the rst time, check to make sure that

your household power supply corresponds to the voltage listed on

the device.

• LCD panel - The LCD panel is made of glass and may break if the unit

is dropped or impacted.

• Heat sources - Keep the product away from heat sources such as

radiators, stoves, heaters and other heat-generating products.

• Water and moisture - Do not use the unit in or near water or in high

moisture areas such as bathrooms.

• Power cord - If the power cord is damaged, it must be replaced by

the manufacturer, its service agent or similarly qualied persons in

order to avoid a hazard.

• Repair - Do not attempt to repair or modify the unit yourself.

Contact the retailer or a qualied repairman if the product requires

servicing. Only use replacement parts that are recommended by the

manufacturer.

• Danger of suffocation! Keep all packaging material away from children.

CARE

This product is designed to give you years of service if handled properly.

Oregon Scientic will not be responsible for any deviations in the usage of

the device from those specied in the user instructions or any unapproved

alterations or repairs of the product. Observe the following guidelines:

• Attention!

Before cleaning disconnect the power plug from the socket.

• Cleaning - Use a damp cloth to wipe the unit. Do not use liquid

cleaning agents, benzene, thinner or aerosols.

• Projector lens - A dirty lens can result in a blurred projection. From time

to time, check to see if dust or other dirt has collected on the lens. Dust:

blow the dust from the lens with a brush/blower made for cameras

(available at an authorised dealer). After that, brush the lens lightly with

the brush and then blow dust off the lens again.

Fingerprints: If the lens does not become clean by using the brush/

blower, use a cotton swab, dipped in a special cleaning solution and

remove the dirt beginning from the middle and proceeding to the outside.

• Do not scratch the LCD display with hard objects.

• Never immerse the product in water. This can cause electrical shock

and damage the product.

• Do not subject the main unit to extreme force, shock, or uctuations in

temperature or humidity.

• Do not tamper with the internal components.

• Ventilation - The vents and other openings are designed to keep the

unit cool and should not be blocked or covered. Preventing ventilation

can lead to overheating and may damage the unit.

ADVICE REGARDING BATTERIES

• Do not expose batteries to extreme heat like direct sunlight, re, etc.

• Batteries do not belong in household waste! Expired batteries must

be disposed of in an environmentally friendly way and according to

the applicable legal regulations.

• Batteries are very dangerous if swallowed. Please keep expired

batteries away from children at all times. If a battery is swallowed,

seek medical attention immediately.

• Batteries must not be recharged or activated with another means,

dismantled, thrown into re or short-circuited.

• Do not mix new and old batteries or batteries of different types.

• Do not use rechargeable batteries with this product.

• Remove the batteries if storing this product for a long period of time.

• The batteries must be removed prior to disposing of the device.

NOTE

The technical specication of this product and contents of this user

guide are subject to change without notice. Images not drawn to scale.

ABOUT OREGON SCIENTIFIC

Visit our website www.oregonscientic.com to learn more about

Oregon Scientic products.

For any enquiry, please contact our Customer Services at

[email protected].

Oregon Scientic Global Distribution Limited reserves the right to interpret

and construe any contents, terms and provisions in this user manual and

to amend it, at its sole discretion, at any time without prior notice. To the

extent that there is any inconsistency between the English version and

any other language versions, the English version shall prevail.

FCC STATEMENT

This device complies with Part 15 of the FCC Rules. Operation is subject

to the following two conditions: (1) This device may not cause harmful

interference, and (2) This device must accept any interference received,

including interference that may cause undesired operation.

WARNING

Changes or modications not expressly approved by the

party responsible for compliance could void the user’s authority to

operate the equipment.

NOTE

This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy

and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is

no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on,

the user is encouraged to try to correct the nterference by one or more of

the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

Consult the dealer or an experienced radio / TV technician for help.

DECLARATION OF CONFORMITY

The following information is not to be used as contact for support or sales.

Please call our customer service number

(listed on our website at www.oregonscientic.com),

or on the warranty card for this product for all inquiries instead.

We

Name: Oregon Scientic, Inc.

Address: 10778 SW Manhasset Dr.

UNIT B-2 Tualatin,

OR 97062 USA

Telephone No.: 1-800-853-8883

declare that the product

Product No.: BAA223PNH

Product Name: Projection Clock

Manufacturer: IDT Technology Limited

Address: Block C, 9/F, Kaiser Estate,

Phase 1, 41 Man Yue St.,

Hung Hom, Kowloon, Hong Kong

is in conformity with Part 15 of the FCC Rules. Operation is subject

to the following two conditions: 1) This device may not cause harmful

interference. 2) This device must accept any interference received,

including interference that may cause undesired operation.

EU-DECLARATION OF CONFORMITY

Hereby, Oregon Scientic, declares that this Projection Clock

(Model: BAA223PNH) is in compliance with EMC directive 1999/5/

EC. A copy of the signed and dated Declaration of Conformity is

available on request via our Oregon Scientic Customer Service.

SC

产品描述

谢谢阁下选购Oregon Scienti󺖞c

TM

PRYSMA B 稜光溫度投影時計。

此装置集精确时计、闹钟及温度监察功能于一身，十分适合于家居中

使用。使用新产品时，请将此手册存放于当眼的地方。手册中包含各

步骤的使用说明，以及你需要留意的技术规格及警告。

产品简介

LCD 显示屏

天气预报

显示

户内温度显示户外温度显示

时间显示

LCD显示屏符号

符号 描述 功能

户外装置 (RTHN129)的

无线电讯号接收

指示无线电讯号接收的强度

电量不足

表示户外装置 (RTHN129)

的电量不足

闹钟 1 已开启

闹钟2 已开启

当闹钟启动时，

此图标便会显示

调频图标

当收到调频的时钟数据时，

此图标便会显示

OUT

12345

户外传感器读数 显示所选传感器的户外温度

IN

户内传感器读数 显示户内温度

ZONE

时间区域 显示所选的时间区域

天晴 天气预报显示

下雨 天气预报显示

下雪 天气预报显示

投影器

显示时间

显示户外温度 (只限频道 1)

注意:

距离范围(1.5 米 – 2 米)

开始使用

将电源连接至设备

把电源线连接至Micro USB 端口，然后把电源插头插入适合的电源

插座中。

把电池装入远程热能传感器

• 滑动电池槽盖以开启，并如图示般配合极性来放入2 粒「AAA」电

池，然后放回电池槽盖。

• 每次更换电池后，请按下传感器中的RESET (重置) 键。

放置主装置

• 把装置尽量放置得远离计算机及微波炉，以避免接收障碍。

• 只在户内的干燥环境中使用此装置。

• 请在装置周围预留空间以作通风之用，以令暖空气得到流通。

• 要确保声音质量良好，请勿遮盖扬声器。

放置远程热能传感器(RTHN129)

Max 1.5m

Max 50m

• 放置传感器的理想地方，是家居户外任何不高于5 英呎(1.5 米)的位

置，并需避免放置在阳光直射和潮湿的环境下。

注

视乎环境而定，无线电讯号传输最远可达50米。

按钮描述

顶部

小睡 (背面灯 / 投影) 按钮

背面

温度按钮 时钟按钮

设置/闹钟按钮 按钮

按钮

Micro USB 插头 重置按钮

°C/°F按钮 灯光按钮

180°转向按钮

无线电接收

当此产品在无线电讯号范围时，它可自动同步行事历及时钟。当装

置接收讯号时，无线电接收符号 (RCC) 会开始闪动。视乎讯号的强

度，连接程序需时2 至10 分钟。如果讯号弱，装置可能需要24 小时

来接收有效的讯号。

符号 描述 功能

无调频天线图标

此图标不显示，表示主装置已至少1 小

时15 分钟没有收到调频的时钟数据

调频天线图标亮

着亮起

此图标亮起表示主装置已收到调频的

时钟数据。

如主装置在1 小时15 分钟都没有数据，

或时钟时间以手动方式来调敎，此图示

便会不显示。

主装置可以从远程传感器，接收调频的时钟数据 (格式为DCF (欧洲)、

MSF (英国)及WWVB (美国)：

• DCF (欧洲)及MSF (英国)：参照DCF/MSF 广播讯号的时区0，时间

区域的设置在-23 至23 的范围内。

• WWVB (美国)：参照WWVB 广播讯号的时区P/M/C/E，时间区域

的设置为0/1/2/3。

时钟讯号接收指示器：

符号 描述

强讯号

弱讯号

没有讯号l

正在接收讯号

已关闭无线电接收

•

注

接收会受到几个原因所影响。要得到最好的接收，请把装置

远离金属对象及电器用品。其他讯号阻碍的原因包括电力传输塔、

钢筋施工及金属壁板。如希望得到最佳的接收效果，请把装置放

于窗边。

开启/关闭无线电接收

SEARCH (搜索) 按钮(位于户外接收器中)

• 按下SEARCH (搜索) 来开启RCC 搜索功能。LED 灯会闪动两次，表

示搜索功能已开启。

• 长按SEARCH (搜索)来关闭RCC 搜索功能。LED 会闪动三次来表

示功能已关闭。

手动设置时间

• 长按SEARCH (搜索) (按钮位于户外接收器中) 以关闭讯号接收。长

按 。画面会显示ZONE (区域)，号码会闪动。

• - 按一次或长按

及 来调整设置。对于欧洲/英国，时区偏移会从

接收到的时钟讯号时间，来设置时钟最多为+/- 23 个小时。至于美

国，时区设置为0(P)、1(M)、2(C)、3(E)。

• 按

以确定。

• -单击或长按

及 来调教 12/24 小时格式、小时、分钟、年份、

行事历格式 (月-日/日-月)、月份、日期及温度单位 (°C/°F).

• 再按

以确定。

显示时间及日期

• 按 以在时间和日期显示之间切换。

闹钟功能

利用此时钟，你可以设置两个不同的响闹时间。

设置/调敎响闹时间

• 长按

.

• 使用

及 来调教小时并按 来确定。

• 使用

及 来调教分钟并按 来确定。

• 装置会显示响闹时间，而响闹声音会于2 分钟后停止。

贪睡回叫功能

• 要使用SNOOZE (贪睡回叫) 功能，请当响闹响起时，在时钟的顶部

按SNOOZE (light) (贪睡回叫(灯光))按钮。8 分钟后响闹会停止并再

次开始。你可以重复此功能三次。

显示响闹时间

默认下，时钟会显示现时时间及日期。

• 要持续5秒来显示响闹1，请按

及 。

• 要持续5秒来显示响闹2，请按

及 。

启动/关闭闹钟

• 按

以启动/关闭闹钟，次序为：

闹钟 1 >闹钟2 > 同时开启两个闹钟 >同时关闭两个闹钟。

背面灯

• 按Light(灯)按钮，以将背面灯的光暗度切换成喜欢的显示程度。

• 如要将投影功能及最高光暗度的背面灯启动5秒，请按Snooze

(light)(小睡(灯))按钮。

常见问题

有关本说明书的更多信息

我们知道，为您的 Oregon BAA 223PNH 气象站 提供纸质手册是件好事。 您随时可以从我们的网站下载该手册并自行打印。 如果您想要原始手册，我们建议您联系Oregon。 他们也许能够提供原始手册。 您是否正在寻找其他语言版本的 Oregon BAA 223PNH 气象站 手册？ 在我们的主页上选择您的首选语言并搜索型号以查看我们是否有可用。

规格

Oregon 气象站 的所有手册
气象站 的更多手册

关于 Oregon BAA 223PNH 气象站 的常见问题

我们的支持团队将搜索有用的产品信息并回答常见问题。如果您在常见问题中发现不准确的回答，请使用联系表格告知我们。

相关产品

说明书

Oregon BAR 623PH 气象站

说明书

Oregon BAA 292H 气象站

说明书

Oregon JW103 气象站

说明书

Oregon BAR 292 气象站

说明书

Oregon BAR 368P 气象站

说明书

Oregon TW 223 气象站

说明书

Oregon BAR 986HG 气象站

说明书

Oregon BAR 200U 气象站

相关类别