说明书 星崎电机IM-130A制冰机
需要您的 星崎电机IM-130A制冰机 手册吗？ 您可以在下面免费查看和下载中文版 PDF 手册。 该产品目前有 0 个常见问题，0 条评论，有 0 票。 如果这不是您想要的手册，请联系我们。
您的产品是否出现故障而说明书没能提供解决方案？请前往 Repair Café 以获得免费维修服务。
说明书
Loading…
5
ENGLISH
* Usually an electrical permit and services of a licensed electrician are required.
* If the supply cord is damaged, it must be replaced by a replacement cord available from Hoshizaki Parts/Service Centres.
7. WATER SUPPLY AND DRAIN CONNECTIONS
WARNING
Connect to potable water supply only.
* The connections to the mains water supply must be made in accordance with the countries’ current requirements of the Water
Supply or Water Fittings Regulations.
* Icemaking water must be potable water. Where scaling can be caused by water quality:
- Installation of an external lter or softener is recommended. Contact your local water treatment professional or Hoshizaki
service agent.
- Change to the “full drain ush” mode is recommended. Contact your local Hoshizaki service agent.
* Water supply pressure should be minimum 0.07 MPa (0.7 bar) and maximum 0.78 MPa (8 bar). If the pressure exceeds 0.78
MPa (8 bar), use a proper pressure reducing valve. Do NOT throttle back the supply tap.
* A plumbing permit and services of a licensed plumber may be required in some areas.
* The icemaker drain is gravity ow, so ensure drain pipe has an adequate pitch or fall.
* Drain lines should not be piped directly to the sewer system. A vertical air gap of a minimum of 5 cm
should be between the end of the drain pipes from the icemaker and the oor drain.
* To prevent a backow into the storage bin, the outlet hose must be laid as shown.
* Be sure to use the new hose-sets supplied with the appliance. Do not reuse any old hose-sets.
1) Attach the angled end of white exible inlet hose (accessory) to the G3/4
tting on the rear side of the icemaker as indicated, ensuring rubber sealing
washer is correctly positioned. Hand tighten sufciently to provide leak free
joint.
2) Attach the other end of inlet hose to the water tap, noting washer is correctly
positioned before hand tightening as above. It is a wise precaution to have a
stop valve within easy reach.
3) Hand tighten grey exible outlet hose (accessory) onto the R3/4 tting on
the rear of the icemaker as indicated, ensuring rubber washer is correctly
positioned to obtain a leak free joint. The pipe can be cut to length as
necessary to suit position of main drain.
5cm air gap
Drain
Floor
Downgrade
GOOD BAD
Upgrade
BAD
Inlet Hose
Outlet Hose
Loading…
常见问题
请给产品评分，告知您对星崎电机IM-130A制冰机看法。您是否希望分享对该产品的体验或提出问题？请在页面底部留言。有关本说明书的更多信息
我们知道，为您的 星崎电机IM-130A制冰机 提供纸质手册是件好事。 您随时可以从我们的网站下载该手册并自行打印。 如果您想要原始手册，我们建议您联系Hoshizaki。 他们也许能够提供原始手册。 您是否正在寻找其他语言版本的 星崎电机IM-130A制冰机 手册？ 在我们的主页上选择您的首选语言并搜索型号以查看我们是否有可用。
规格
| 品牌 | Hoshizaki |
| 模型 | IM-130A |
| 类别 | 制冰机 |
| 文件类型 | |
| 文件大小 | 2.04 MB |
加入有关该产品的对话
您可以在这里分享您对 星崎电机IM-130A制冰机 的看法。 如果您有疑问，请先仔细阅读手册。 可以使用我们的联系表索取手册。